Nylopick Sheets can work satisfactorily as Linear material for Hoppers, Silos and Chutes, Anti-sticking character of Nylopick prevents any caking or freezing of Silos content on the surface of Silos, Hoppers, separators and similar plants. The major advantage of Nylopick Lining is easy release and slidablity and, therefore it is obvious that clogging of materials being experienced by you frequently at present may not occur; on the contrary, by deploying Nylopick Lining, maintenance of continuous flow will be natural.
| TABLE WEAR LOSS - NYLOPICK | |
|---|---|
| UMPWPE | 17 |
| ABRASION RESISTANT STEEL | 55 |
| STAINLESS SEEL | 84 |
| CARBON STEEL | 100 |
| PHOSPHOR BRONZE | 193 |
| NYLON 6-6 | 31 |
| POLYURETHANE (D-70) | 37 |
| HDPE | 86 |
| LOW DENSITY POLYETHYLENE 5 | 30 |
| THE ABOVE PROPERTIES ENABLE NYLOPICK TO BE USED AS LINEAR CONVEYOR, IDLER, WHEEL ETC. | |
THE ABOVE PROPERTIES ENABLE NYLOPICK TO BE USED AS LINEAR CONVEYOR, IDLER, WHEEL ETC.
Nylopick liners can be fitted to steel or concrete. Bunkers , chutes, silos etc. The surface on which the liners are to be fitted must be reasonably flat and clean. Correct mounting of nylopick wear liner can assure satisfactory performance. In case liner plates are exposed to sunlight, black, uv-resistant liners should be used. While installing the liners the coefficient of expansion of uhmw polyethylene “Nylopick” must be taken into conside ation, since it is about 8 times lighter than steel. As such it is always recommended to mount the liners at the normal temperature of operation.
The liners are normally laid lengthwise in the direction of flow of bulk material, each plate overlapping the next one by about 15 mm horizontally. Vertical joints are put edge to edge according to the necessities, liners can also be put with horizontal and vertical joints edge to edge but staggered without any problem. Whenever lining has to be done on a curved surface without many divisions; several grooves are made on the backside of the liner to suit the corresponding region. In case of part of lining of bunkers, the upper-most edge of the liner plate is covered by steel strips as safeguard against seepage of fine dusts. The high resistance of uhmw polyethylene to solvents restricts the range of suitable adhesives for gluing with these bonding agents only moderate joint strength is achieved. There fore, the liners are fastened with mechanical fasteners like counter-sunk bolt, screw, dowel etc. For lining concrete silos fastening done by means of countersunk bolt with straddling dowel. In the case of steel silos liners are fastened by means of counter-sunk head bolts with nuts when mother plate can not be wasted. The pitch between the fasteners depending on the thic ness of the liner is maintained at 150 to 200 mm. A distance of about 50 mm is left from the edge of the liner while fixing the bolt.
USUAL RECOMMENDED THICKNESS OF LINER IS 10 & 20 MM. IN CRUCIAL CORNER THICKNESS CAN BE INCREASED. NYLOPICK LINERS ARE AVAILABLE IN THICKNESS UP TO 75 MM AND ABOVE.
NYLOPICK SPARE PARTS FOR MINING AND METAL PROCESSING INDUSTRIES
MYLOPICK is specially formulated polymer for bulk material handling in mining, conveying, storage and transportation. Typical problems of bulk material storage like arching, shaft formation, caking and irregular discharge is taken care of NYLOPICK because of its good sliding properties and excellent abrasion resistance it outwears stainless steel by almost 2:1 ratio.
| TECHNICAL DATA | ||
|---|---|---|
| Property | Test Method | Unit |
| Density | ISO 1183 | g/cm3 |
| Molecular weight | - | Mil/mol |
| Tensile Strength | ISO 527-1 | Mpa |
| Breaking Strength | ISO 527-1 | Mpa |
| Elongation at Break | ISO 527-1 | % |
| Modulus of elasticity | ISO 527-1 | Mpa |
| Impact Strength 15° V Notch | ISO 179 | Kj/m2 |
| Shore Hardness D 15 s | ISO 868 | - |
| Wear Resistance by sand slurry method | Internal test method | - |
| Width | Length | Thickness |
|---|---|---|
| 1230 | 4300 | 20-75 mm |
| 1230 | 1990 | 08-175 mm |
| 1000 | 2000 | 06-50 mm |
| 660 | 3000 | 20-100 mm |
| Dia | 10 mm to 250 mm | |
|---|---|---|
| Standard Length | 1 metre | |
| Special length and colour available on request. | ||